ASTM A960 Wrought Fitting Requirements: What Buyers Must Know
ASTM A960 sets common requirements for wrought steel pipe fittings covered by individual ASTM product specs like A234. This guide explains what buyers must verify when ordering and inspecting fittings.
September 27, 2026·5 min read·Hebei Haihao Group
法兰管件图.jpg
Purpose of ASTM A960
ASTM A960/A960M, Standard Specification for Common Requirements for Wrought Steel Piping Fittings, establishes a set of requirements that apply broadly to wrought steel piping fittings when invoked by an individual ASTM product specification. It is not a grade specification. The document covers common material, manufacturing, heat treatment, chemical analysis, and mechanical testing expectations that must be considered together with the specific product specification.
For example, A234/A234M covers wrought carbon steel and alloy steel fittings for moderate and high temperature service. A960 is the common-requirements backbone for such fittings.
Relationship with Product Specifications
A960 is intended to be used with product specifications that invoke it. The scope of A960 lists several specifications, including:
A234/A234M – Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and High Temperature Service
If there is a conflict between A960 and the individual product specification, the individual specification prevails. That means buyers must always check both documents.
Material and Manufacturing Requirements
A960 states that the material for fittings shall consist of forgings, bars, plates, and seamless or welded tubular products. Ferritic steels must be fully killed. Hollow cylindrically shaped parts up to and including NPS 4 may be machined from bar or seamless tubular material. However, elbows, return bends, tees, and header tees must not be machined directly from bar stock.
These manufacturing constraints matter for procurement. If you are sourcing small fittings, confirm that the production method is compliant with A960 and the product specification.
Heat Treatment and Testing
A960 lists the heat treatment procedures that may be used: full annealing, solution annealing, isothermal annealing, normalizing, tempering and post-weld heat treatment, stress relieving, and quench and temper. The appropriate treatment depends on the grade and the product specification requirements.
Chemical analysis and product analysis are required. The chemical requirements apply to carbon, manganese, phosphorus, sulfur, silicon, nickel, chromium, molybdenum, vanadium, columbium, titanium, aluminum, lead, and copper.
Mechanical testing includes tension, hardness, impact, and hydrostatic tests. Buyers should not assume that all tests are always required for every grade; the product specification determines which tests apply.
What Buyers Must Verify
Because A960 does not replace the grade-specific requirements, the purchase order must clearly identify:
The invoking product specification, such as A234/A234M.
The grade, such as WPB or WPC.
Whether the order is to be furnished in inch-pound or SI units. If the “M” designation is not specified, the material is furnished in inch-pound units.
The edition or revision of the specifications to be used.
Any supplementary requirements, such as S58 in A960 for fittings that differ from ASME or MSS standards.
A960 also allows additional requirements to be added by mutual agreement between purchaser and supplier. Those additional requirements must be included in the order.
RFQ Checklist
When preparing an RFQ for wrought steel fittings, include at minimum:
The standard designation and grade, e.g., ASTM A234 WPB.
The dimensional standard, such as ASME B16.9 or B16.11.
Size, schedule, and fitting type.
Whether SI or inch-pound units are required.
Any supplementary requirements from A960 or the product specification.
Test requirements, if you need to specify them.
Documentation requirements, including EN 10204 3.1 or 3.2 certificates if applicable.
If you are sourcing from a supplier, it is prudent to request the full mill test certificate and confirm that the supplier has purchased the correct current edition of the standards. ASTM standards are updated regularly; an older edition may not reflect current requirements.
For a complete range of butt-weld fittings and flanges, visit our /en/products page. If you have specific technical requirements, you can send an inquiry via /en/inquiry.
Inspection and Documentation
Incoming inspection should verify that the fittings are marked in accordance with the applicable standard and that the marking matches the documentation. Review the MTC for heat treatment, chemical composition, and mechanical test results.
For dimensional inspection, compare against the ASME or MSS standard specified in the order. For example, A234 covers fittings that comply with ASME B16.9, B16.11, MSS-SP-79, SP-83, SP-95, and SP-97. If the fittings are manufactured to a different geometry, they must be furnished in accordance with Supplementary Requirement S58 of A960.
You may also request third-party inspection, but remember that A960 does not automatically require NDT or third-party witness. These are typically specified as supplementary requirements.
Common Risks
A common mistake is treating A960 as if it were the full product specification. A960 covers common requirements only. Grade-specific chemistry, mechanical properties, and heat treatment parameters are defined in the product specification.
Another risk is overlooking the unit system. If the order does not specify the “M” designation, the supplier will furnish material to inch-pound units. This can lead to misunderstandings if the buyer expects SI units.
A third risk is failing to identify supplementary requirements. If the fitting does not conform to standard ASME or MSS dimensions, S58 of A960 is invoked, and you should ensure the supplier is aware.
Sources
https://store.astm.org/a0960_a0960m-25a.html
https://store.astm.org/a0234_a0234m-26.html
Need a quote for the products mentioned in this article?
Submit your specs and our pressure piping team will respond within one business day.
Grain size testing under ASTM A182 is mandatory only for certain grades. Learn when ASTM E112 applies, which methods are used, and what buyers must verify before accepting a fitting.
Charpy impact records for pipe fittings often include subsize specimens. Learn what ASTM E23 and A370 actually require, and where acceptance criteria must be found.
Weld repair acceptance for A234 and other wrought steel fittings is governed by the product specification, A960/A960M common requirements, and the purchase order — not by a generic visual pass/fail rule. Here's what to verify.
Oct 2, 20268 min readHebei Haihao Group
Quote in 4 hours
Products covered in this article
Sourcing any of these? Send the spec and our pressure-piping desk replies within 4 business hours.
